Olympia Chimney Chimney Liner & Rebuild Nationwide

Olympia Chimney Chimney Liner & Rebuild in Norwood: What to Know First

We provide independent Olympia Chimney chimney liner and rebuild work in Norwood, and most liner jobs are finished in a single day once we’re on site. A stainless liner replacement on a typical Norwood single-flue chimney runs roughly $1,800 to $3,400, while a partial rebuild above the roofline lands between $2,500 and $5,000 depending on access and brick condition. We’ll give you a firm number before any tool comes off the truck.

Call (508) 687-5884

If you own a home in Norwood with an Olympia Chimney system and you’re seeing flaking tile, a rusted damper, or water staining around the hearth, this page tells you what’s actually going on and what it takes to fix it. Call (508) 687-5884 and Wendell or one of his crew will pick up.

How Olympia Chimney Products Fail - and How We Fix Them

Olympia Chimney builds solid systems, but Norwood’s freeze-thaw cycles and the damp air off the Neponset River basin push every liner harder than the manufacturer’s average case. Here’s what we see most often:

• Olympia Forever Flex liners kinking at the smoke shelf. The Forever Flex is a good flexible liner, but when a Norwood home’s original clay tile has already shifted, the flex liner follows the misaligned path and folds at the shelf. The tell is a whistling draft and back-puffing on windy days. We pull the old liner, straighten the run with a proper guide cone, and insulate to keep the curve honest.
• Rigid stainless sections separating at the mid-flue joint. Olympia’s rigid liner sections rely on a locking band, and we’ve seen those bands corrode on Norwood chimneys within eight to ten years when the crown wasn’t shedding water. The sections separate under thermal expansion, and exhaust leaks into the chase. Fix is a full rigid-liner swap with a new crown and rain cap, not a patch.
• Damper plates welded open by creosote on wood-burning setups. Norwood burns a lot of mixed hardwood, and Olympia dampers on uncapped chimneys get a glaze of third-degree creosote that seizes the plate. We don’t force it. We camera the flue, document the glaze, and replace the damper before it breaks off and blocks the throat.
• Chase-top rust-through on Olympia pre-fab boxes. Homes along Washington Street with older Olympia zero-clearance units show rusted chase tops and leaking flue collars. The galvanized top fails before the stainless body, and water runs down the outside of the liner into the firebox. We rebuild the chase top, replace the collar, and reseal the whole penetration.
• Brick spalling around the Olympia termination cap. The cast cap on older Olympia systems is heavy, and when the crown underneath cracks, water gets trapped between the cap base and the brick. Norwood winters freeze it, and the top three courses start crumbling. We remove the cap, rebuild the crown with a proper slope, and reset or replace the termination.

Our Olympia Chimney Chimney Liner & Rebuild Process

Every Olympia job follows the same sequence, and we don’t skip a step:

1. 1
   Camera inspection first. We run a camera down the flue before a single recommendation is made. You watch the footage on our screen. If the liner is fine, we’ll tell you it’s fine and head back to the truck.
2. 2
   Plain-English verdict. Wendell explains what the camera showed in words you don’t need a dictionary for, and he writes the price down. That number does not change unless the house reveals something hidden, and we’ll call you first.
3. 3
   Parts decision. When OEM Olympia parts make sense, we use them. When a quality aftermarket liner like DuraFlex or HeatShield does the same job for less, we show you both and let you decide.
4. 4
   The work. Liner replacement, partial rebuild, full rebuild, whatever the job is. We protect the hearth and floors, and we don’t leave a mess on the lawn or the roof.
5. 5
   Post-install test. We run a draft check and a final camera pass so you see the finished run, not just our word for it.
6. 6
   90-Day Done Right Promise in writing. If it’s not right, one call brings Wendell back at no additional cost.

What Olympia Chimney Chimney Liner & Rebuild Costs in Norwood

Here are honest ranges for the Olympia jobs we handle most in Norwood. These are Norwood numbers, not national averages:

• Olympia flexible stainless liner replacement, single flue: $1,800-$3,400
• Rigid stainless liner, single flue with insulation: $2,600-$4,500
• Partial rebuild above the roofline, brick and crown: $2,500-$5,000
• Full chimney rebuild from the firebox up: $6,000-$12,000
• Damper replacement on an Olympia firebox: $350-$900
• Chase top rebuild on a pre-fab Olympia unit: $800-$2,200

What moves the price: flue height, roof pitch, whether scaffolding is needed, and whether the brick is salvageable. We’ll give you a fixed quote before work starts, and remember the standing offer: $40 off any repair over $200, and free second opinions on any competing written estimate. Call (508) 687-5884 for exact numbers on your chimney.

Why Norwood Homeowners Call Top Hat Chimney for Olympia Chimney Work

Wendell Pike founded Top Hat Chimney in 1999, and he’s been working chimneys in Norwood and the surrounding towns for over 29 years. He grew up in San Diego, but chimneys pulled him east, and Norwood is where he and his crew have put in most of their work. He learned the trade at Palomar College’s vocational program and stopped counting jobs somewhere past a thousand.

When you call, a live person answers. It may well be Wendell. We don’t have a call center, and we don’t dispatch strangers. The sweep who shows up at your door is background-checked, in uniform, and works for the company whose name is on the truck. We install and service Olympia Chimney products alongside DuraFlex, HeatShield, and Gelco, so if your Olympia flue needs a liner that Olympia doesn’t make in the right size, we have options that fit. Every job ends with the 90-Day Done Right Promise, in writing, on the invoice. If it doesn’t need doing, we’ll tell you that too.

FAQs